function b = middleearfilter(fs,varargin)
%MIDDLEEARFILTER   Middle ear filter
%   Usage: b=middleearfilter(fs,varargin);
%          b=middleearfilter(fs);
%          b=middleearfilter;
%
%   MIDDLEEARFILTER(fs) computes the filter coefficients of a FIR
%   filter approximating the effect of the middle ear.
%
%   The following parameter and flags can be specified additionally:
%
%     'order',order  Sets the filter order of the computed FIR filter.
%                    Default value is 512.
%
%     'minimum'      Calculates a minimum phase filter. This is the default.
%
%     'zero'         returns a filter with zero phase. Since Matlab shifts the
%                    symmetric impulse response due to no negative indices.
%                    This results in a linear phase and hence a delay in the 
%                    signal chain.
%
%     'lopezpoveda'  Use data from Lopez-Poveda and Meddis (2001). These
%                    data are in turn derived from Goode et al. (1994).
%                    This is the default. 
%
%     'jepsenmiddleear'  Use the data originally used for the Jepsen 2008
%                        model.
%
%   MIDDLEEARFILTER without any input arguments returns a table describing
%   the frequency response of the middle ear filter. First column of the
%   table contain frequencies and the second column contains the amplitude
%   (stapes peak velocity in m/s at 0dB SPL) of the frequency like in figure
%   2b) of Lopez-Poveda and Meddis (2001).
%
%   MIDDLEEARFILTER is meant to be used in conjunction with the LOPEZPOVEDA2001
%   function, as the output is scaled to make lopezpoveda2001 work. If you are not
%   using the lopezpoveda2001, you probably do not want to call this function. The
%   following code displays the magnitude response of the filter:
%
%     fs=16000;
%     x=erbspace(0,fs/2,100);
%     b=middleearfilter(fs);
%     H=freqz(b,1,x,fs);
%     semiaudplot(x,10*log10(abs(H).^2));
%     xlabel('Frequency (Hz)');
%     ylabel('Magnitude (dB)');
%
%   See also:  data_lopezpoveda2001, lopezpoveda2001
% 
%   References:
%     R. Goode, M. Killion, K. Nakamura, and S. Nishihara. New knowledge
%     about the function of the human middle ear: development of an improved
%     analog model. The American journal of otology, 15(2):145-154, 1994.
%     
%     E. Lopez-Poveda and R. Meddis. A human nonlinear cochlear filterbank.
%     J. Acoust. Soc. Am., 110:3107-3118, 2001.
%     
%
%   Url: http://amtoolbox.sourceforge.net/amt-0.9.9/doc/general/middleearfilter.php

% Copyright (C) 2009-2015 Piotr Majdak and the AMT team.
% This file is part of Auditory Modeling Toolbox (AMT) version 0.9.9
%
% This program is free software: you can redistribute it and/or modify
% it under the terms of the GNU General Public License as published by
% the Free Software Foundation, either version 3 of the License, or
% (at your option) any later version.
%
% This program is distributed in the hope that it will be useful,
% but WITHOUT ANY WARRANTY; without even the implied warranty of
% MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
% GNU General Public License for more details.
%
% You should have received a copy of the GNU General Public License
% along with this program.  If not, see <http://www.gnu.org/licenses/>.

%   AUTHOR: Peter L. Søndergaard, Katharina Egger

%% ------ Check input options --------------------------------------------

% Define input flags
definput.flags.filtertype = {'lopezpoveda','jepsenmiddleear'};
definput.flags.phase = {'minimum','zero'};
definput.keyvals.order = 512;

% Parse input options
[flags,kv]  = ltfatarghelper({},definput,varargin);

if flags.do_lopezpoveda
  
  data = data_lopezpoveda2001('fig2b', 'noplot');
  
  if nargin==0
    b = data;
  else
    if fs<=20000
      % In this case, we need to cut the table because the sampling
      % frequency is too low to accomodate the full range.
      indx=find(data(:,1)<fs/2);
      data = data(1:indx(end),:);
    else
      % otherwise the table will be extrapolated towards fs/2
      % data point added every 1000Hz
      lgth = size(data,1);
      for ii = 1:floor((fs/2-data(end,1))/1000)
        data(lgth+ii,1) = data(lgth+ii-1,1) + 1000;
        % 1.1 corresponds to the decay of the last amplitude values = approx. ratio
        % between amplitudes of frequency values seperated by 1000Hz
        data(lgth+ii,2) = data(lgth+ii-1,2) / 1.1; 
      end
    end;  
    
    % for the function fir2 the last data point has to be at fs/2
    lgth = size(data,1);
    if data(lgth,1) ~= fs/2
      data(lgth+1,1) = fs/2;
      data(lgth+1,2) = data(lgth,2) / (1+(fs/2-data(lgth,1))*0.1/1000);
    end
    
    % Extract the frequencies and amplitudes, and put them in the format
    % that fir2 likes.
    freq=[0;...
          data(:,1).*(2/fs);...
         ];
    ampl=[0;...
          data(:,2);...
         ];
    
    b = fir2(kv.order,freq,ampl);
    
    b = b / 20e-6;      % scaling for SPL in dB re 20uPa
    
    if flags.do_minimum
      X = fft(b);
      Xmin = abs(X) .* exp(-i*imag(hilbert(log(abs(X)))));
      b = real(ifft(Xmin));        
    end
    
  end
  
end;

if flags.do_jepsenmiddleear
    
  stapes_data = [...
      50,	 48046.39731;...
      100, 24023.19865;...
      200, 12011.59933;...
      400,  6005.799663;...
      600, 3720.406871;...
      800,  2866.404385;...
      1000, 3363.247811;...
      1200, 4379.228921;...
      1400, 4804.639731;...
      1600, 5732.808769;...
      1800, 6228.236688;...
      2000, 7206.959596;...
      2200, 9172.494031;...
      2400, 9554.681282;...
      2600, 10779.64042;...
      2800, 12011.59933;...
      3000, 14013.53255;...
      3500, 16015.46577;...
      4000, 18017.39899;...
      4500, 23852.82136;...
      5000, 21020.29882;...
      5500, 22931.23508;...
      6000, 28027.06509;...
      6500, 28745.70779;...
      7000, 32098.9;...
      7500, 34504.4;...
      8000, 36909.9;...
      8500, 39315.4;...
      9000, 41720.9;...
      9500, 44126.4;...
      10000,46531.9;...
                ];
  
  % We need to find inverse because original data is stapes impedance and we
  % need stapes velocity.
  stapes_data (:,2) = 1./stapes_data(:,2); 
  
  if nargin==0
    b = stapes_data;
  else
    
    if fs<=20000
      % In this case, we need to cut the table because the sampling
      % frequency is too low to accomodate the full range.
      
      indx=find(stapes_data(:,1)<fs/2);
      stapes_data=stapes_data(1:indx(end),:);
    end;  
    
    % Extract the frequencies and amplitudes, and put them in the format
    % that fir2 likes.
    freq=[0;...
          stapes_data(:,1).*(2/fs);...
          1];
    ampl=[0;...
          stapes_data(:,2);...
          0];
    
    b = fir2(kv.order,freq,ampl);
    
    % See the figure text for figure 1, Lopez (2001).
    b = b/max(abs(fft(b)))*1e-8*10^(104/20); 
    
  end;      
  
end;
  
  
  
% if flags.do_plot
%     % Manually calculate the frequency response
%     fmid = abs(fftreal(b));
%     % Half the filter length.
%     n2=length(fmid);
%     % x-values for plotting.
%     xplot=linspace(0,fs/2,n2);
%     loglog(xplot/1000,fmid);
%     xlabel('Frequency (kHz)');
%     ylabel('FIR middleearfilter');
% end